3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [creality-ender-3]

For questions about the Creality Ender 3 family of 3D printers

A low-cost 3D printer clone of the Prusa i3 using aluminium profiles (20 x 20 mm and 20 x 40 mm) with a heated bed. A Bowden style extruder is lifted on a portal style printer with a single Z-axis stepper motor. To date the series consists of the 3, the 3X and the 3 PRO.

750 questions
17
votes
9 answers

First 3 mm prints poorly, then fine after that

I have an Ender 3 that I have been pretty happy with so far, however it recently started an odd behavior and I can't figure out what's causing it. What happens is that the first ~3 mm of the print comes out "sloppy". After that, everything clears…
Steve In CO
  • 889
  • 3
  • 9
  • 18
14
votes
3 answers

Ender 3 nozzle homes off the bed in the Y axis

I just received my new Creality Ender 3. I was going through and checking/adjusting everything for alignment, and I noticed that when you "auto home" the print head, the nozzle stops off the front of the print bed by 5-10 mm. Is that normal? Is it…
Steve In CO
  • 889
  • 3
  • 9
  • 18
12
votes
5 answers

Creality Ender 3 printer power consumption?

Anyone have any idea how much power it takes to run a Creality Ender 3 3D printer every day for several hours at a time? Like what does it eat up per hour? A rough estimate of power use per hour would be nice, then I can figure out how much it costs…
James Hanvey
  • 211
  • 1
  • 3
  • 4
11
votes
3 answers

Why is the center of my glass print bed lower than the corners?

I have a new Creality Ender 3. I suspect that I have not adjusted the eccentric nuts correctly, on the X-axis head carriage mounts. Even after a glass bed upgrade, using the Level Corners routine of the TH3D firmware, I can get the head to scrape…
SPJ
  • 111
  • 1
  • 1
  • 4
11
votes
3 answers

Recalibrating Home-position

I got myself the Ender 3. The Home position is about 1 mm left and 2 mm in front of the front left corner. Now, the hotend center axis is 11 mm from the carrier plate with the "Mk 10" cooler mounted right onto a pair of 5 mm pegs that are part of…
Trish
  • 21,174
  • 10
  • 48
  • 97
11
votes
3 answers

Why doesn't PLA stick to heated bed?

I have a basic Creality Ender-3 with a black rough bed cover. I'm printing with PLA. After assembly, I printed 3 or 4 small toys sliced by Cura with basic settings. All were printed very well! However, after that, extruded filament would not stick…
Roman Matveev
  • 253
  • 1
  • 3
  • 8
10
votes
2 answers

Configuring Marlin 2.x with Ender 3 4.2.2 and BLTouch

I bought an Ender 3 recently and it has the 4.2.2 Creality board. Then I bought a BLTouch to upgrade it with bed leveling. It turns out that the BLTouch now comes with a standard 5-pin connector instead of the separate wires that all the tutorials…
deltree
  • 331
  • 1
  • 2
  • 11
10
votes
4 answers

Expansion in bottom skin after first layer

I'm having an issue where prints with narrow tolerance come out fused. This makes it pretty much impossible to print anything with narrow parts. It seems to be mostly (maybe only) an issue in the bottom skin layers. Once it gets through those, the…
Robert
  • 367
  • 1
  • 5
  • 15
9
votes
1 answer

Extruder doesn't retract on inner wall lines thereby causing stringing

I am trying to stop the stringing that occurs on one of my prints, I have set it so that it retracts the filament which does stop it during the extrusion of the outer wall layer, however when it comes to print the inner lines of the section it does…
Liam
  • 679
  • 4
  • 12
  • 20
9
votes
3 answers

Inductive Sensor in 24 V machine?

I am getting a 24 V based Ender 3. From the factory, it has an aluminium bed. So I also put this LJ12 A3-4-Z/BX Inductive NPN NO 4 mm with 6-36 V operation current into the box together with a few other spare parts. Now, as I read up on these things…
Trish
  • 21,174
  • 10
  • 48
  • 97
9
votes
3 answers

Is there a way to save a multi part print if one fails?

I'm printing 6 separate parts in one go, after 4 hours of printing one part failed, but the other 5 are printing nicely. Is there a way to prevent the print from printing the failed part and continue printing the other 5 parts. I'm using Cura and an…
Nerdroid
  • 193
  • 5
8
votes
3 answers

What voltage does the Creality Ender-3 run at?

I am pondering about buying a Creality Ender-3, and I am honestly confused about some reviews. Some claim it is running 24 V, one did claim it was 12 V, most don't mention it. Since I know about some issues with the clamps, if I get myself an…
Trish
  • 21,174
  • 10
  • 48
  • 97
8
votes
3 answers

Assembled my first 3D-printer: Lead screw problem?

A couple of days ago I got my first 3D printer: Creality 3D Ender 3 Pro. I finished assembling it last night. I booted it up, but ran into problems (which I guess is not a common thing for a beginner in 3D printing). After booting and running the…
Natural Number Guy
  • 183
  • 5
8
votes
3 answers

Where can I change the nozzle diameter in Cura? Why is mine missing?

I just upgraded the nozzle (to 1 mm) on an Ender 3v2 and want to make a test print. I added a new printer for the new nozzle size.... and can't find a setting for it. Some screenshots on the internet show a nozzle diameter setting in the machine…
YetAnotherRandomUser
  • 1,085
  • 3
  • 12
  • 25
8
votes
1 answer

Ender 3 X-axis layer shifting

I've been having a problem lately with some minor layer shifting with my Ender 3. It just started recently and I've made no changes to the printer since it was working fine. The layer shifting is always on the X-axis and it's not a large amount.…
Daknife
  • 331
  • 3
  • 8
1
2 3
…
49 50