Engineering Stack Exchange
Engineering Stack Exchange

Questions tagged [joining]

Use this tag when asking questions about joining/fastening/affixing items together by means of various joining processes like: mechanical fastening,joining by fusion,solid-state joining etc.

21 questions
13
votes
11 answers

Affixing a thermocouple to a surface

I'm looking for advice on how to attach a thermocouple to a metal surface in a fashion that's relatively temperature resistant (more-so than) glue. I've got some very fine gauge wire on hand to make the thermocouples and specialized spot welder…
Dan
  • 1,976
  • 1
  • 11
  • 17
10
votes
3 answers

Bonding Semiconductors to PCB

I'm trying to bond semiconductor samples (Si and Ge) area ~1-2cm^2 to fiberglass printed circuit board (PCB) We use West system marine epoxy for other things. 105 resin 209 hardener (long cure time.) So that's what I used. (mixed at standard ratio)…
George Herold
  • 447
  • 2
  • 9
6
votes
3 answers

Mounting and Coupling an Encoder

I was wondering how to mount a small rotary encoder to a platform in order to measure how far a small treaded robot has traveled. We're using this tread/wheel set: We've tried epoxying the encoder shaft directly to the end of an extra gear wheel,…
rasz
  • 93
  • 5
4
votes
1 answer

How does a union joint with two male threads work?

How does union joint with two male threaded ends work? Does one male end rotate 360 degrees around it axis? How is the inside of the union constructed? Can I connect two pipes with female threads using a union joint and assemble/disassemble it…
Sysrq147
  • 341
  • 2
  • 5
  • 15
3
votes
2 answers

Overcoming limitations of a snap in joint

I have a medical device I am designing which will lie under the patient bed. I need to add a "connector/joint" on this device to permit the attachment of some consumable. Here is a quick overview of the process: Blue part is low cost injected…
Nicolas Goy
  • 133
  • 3
2
votes
3 answers

What type is miter joint - Welding

Is miter joint in welding - butt joint or corner joint ? My example includes 45 degrees miter (90 degrees) angle on two SHS (Square Hollow Sections) - 50x50x3 [mm] Working with EN/ISO norms regarding welding and joint preparation. My opinion is…
Sysrq147
  • 341
  • 2
  • 5
  • 15
1
vote
2 answers

What is a good method of creating a pivot point between flat metal bars?

I could use a hand choosing the mechanism for joining the ends of 2 flat metal bars (each around 3/4" wide and 1/8" thick) so that they pivot freely but without play. What I'm currently planning is to drill a 1/8" hole in one and a 1/4" hole in…
uncaged
  • 71
  • 1
  • 3
  • 5
1
vote
2 answers

Consumable arc welding Polarity Effect on heat input

why DCEP is generally used in consumable welding process? As per my understanding more heat is generated where the electrons collide(anode), so in consumable welding,we want deposition and also want penetration, DCEN would give more heat at the work…
effective-energy-356
  • 45
  • 1
  • 10
1
vote
3 answers

Achieve mechanically water tight snap-in-place joint

I'm not sure how to ask it but i'll try I want to 3d-print 2 half spheres with a screw cap that then can be clipped once (can't un-clip later) And can be filled with water (lets say its food safe, i'll also coat the internal to waterproof it) So,…
Simon
  • 103
  • 7
1
vote
1 answer

Recommendations on a rigid connection between materials

I am trying to construct a torsion pendulum/balance for a physics experiment but the research papers are always missing specifics on how the certain connections are made. I am looking for recommendations on rigid connections for: How to attach a…
axawire
  • 23
  • 4
1
vote
3 answers

How to calculate properties of a thread?

I have a simple thread joint between two objects: and want to find a size of those threads so that after rotating male part it stands at the specific angle. For those who is curious I made it in Fusion 360 and added joints to these parts, also…
Turkhan Badalov
  • 111
  • 2
0
votes
0 answers

How to best friction fit/join two tubes with identical diameters?

I have a number of tubes in a thin aluminum that are identical with each having one side that ends in a hemisphere shape and the other with a cap shape. I'm trying to find more information about trying to friction join the cap ends without the caps…
James Patterson
  • 11
  • 1
0
votes
2 answers

Sleeve nut with non-circular cylinder

I've been scouring the internet for hours to find this type of nut. The requirements are fairly simple: I want to cut holes into two metal sheets to join them with some kind of fastener (e.g. nut and screw). The fastener should be removable. The…
cg_f
  • 1
0
votes
1 answer

how to fix an object at either 90degree or 0 degree

my problem is i donot know how to let the blue colored object be fixed at either 0 or 90 degree. i dnot want to be moveable at any degree like 30, 40 , or 50 degree either 0 or 90 degree. i have tried couple of things but they all waorked at giving…
ABO M7TRAF
  • 1
  • 3
0
votes
2 answers

Locking joints and frame construction

I'm designing a large light art project and I've been trying to find kits that could essentially make lattice-like structures. For example how stages and cranes have lattice structures. The idea would be similar to wire frame floats for parades, but…
lakerice
  • 113
  • 3
1
2