Questions tagged [ender3]
13 questions
4
votes
1 answer
Ender 3 Pro: X-axis moves too much during printing
I got an Ender 3 Pro yesterday and have been having a problem with all of my prints. Whenever the extrusion stops and the X-axis moves, it moves too far. For example, I tried printing a Benchy with 2 skirt lines, and the lines were the right size…
DerFern
- 141
- 7
1
vote
2 answers
Ender 3v2 nozzle plunging into bed after finishing mesh (only changed springs)
Yesterday I was printing just fine. Today I put the new springs that I bought from Amazon. Swapped them out, went to level things and my Z-offset was of course way off.
I have the Ender3V2-422-BLTUBL-MPC-20230904.bin firmware from mriscoc
I homed…
Joleme
- 11
- 2
1
vote
1 answer
Ender 3 S1 Pro error "extrude below min temp"
When I start my print it goes to home the z-axis and then I get the error "extrude below min temp" error (I have an Ender 3 S1 Pro)
Mr. Magic
- 11
- 1
1
vote
0 answers
How would I fix an under extrusion problem?
Hey all I have an Ender 3 V1 and I have a problem with it under extruding. Its not putting out enough PLA to stick and it just becomes a mess. (Bed has a magnetic PEI plate that only has a few uses) Occasionally it will put out a little more on one…
Nick Vitale
- 11
- 1
1
vote
0 answers
How to fix Y axis is off by 30 mm?
I have Ender 3 with Klipper.
In my config:
[stepper_y]
step_pin: PB10
dir_pin: !PB2
enable_pin: !PB11
microsteps: 16
rotation_distance: 40
endstop_pin: ^PC1
position_min: -30
position_endstop: -30
position_max: 200
homing_speed: 50
With this, when…
Alex Buznik
- 111
- 2
1
vote
1 answer
G28 X does not home the hotend
I have a classic Ender 3 running Marlin-2.1.1 on a BTT SKR v1.3 board with TMC 2130 drivers. Wifi is connected with ESP3D on an ESP32-CAM board connected to a TFT port. The X endstop is on the left side.
When I send G28 or G28 X, the hotend does not…
Hansa G
- 33
- 3
1
vote
0 answers
Is it normal that my heated bed has up to 25 °C difference from center to edge?
I have an Ender 3 V2 pro with the Quinly bed adhered to the aluminium bed.
I have a hard time getting my prints to stick well. (PLA as well as PETG). We finally found out that only increasing the bed temperature a lot helps a little. Only the edges…
Hacky
- 649
- 3
- 11
0
votes
1 answer
Ender 3 v2 with CR Touch/BLTouch moving down but not up
My Ender 3 v2 with a CR Touch/BLTouch installed is only moving down, but not up!
The display shows P Endstop when I try to move below around halfway up the gantry. What's going on, and how do I fix this?
zurgeg
- 123
- 6
0
votes
1 answer
The nozzle becomes clogged in the smoothing mode
My nozzle gets clogged when it starts to do smoothing. Settings below:
Мульти студия
- 1
- 2
0
votes
0 answers
Ender 3 S1 Pro extruding/jamming on random layers
My relatively new Ender 3 S1 Pro with default extruder started to under extrude and jam on some layers. When it happens I can hear extruder skipping/clicking noises. I printed same g-code multiple times and happened on different layers.
I replaced…
kzulis
- 1
- 2
0
votes
2 answers
How to fix "SD Init Fail" on Ender 3
My Ender 3 is showing SD Init Fail when the sd card is inserted. I tried rebooting, reformating the card etc. At first, I thought the card is damaged, so I bought a new card. Still the same. I can use the card with the computer without any…
Johnykutty
- 131
- 1
- 5
0
votes
0 answers
Ender 3 CR Touch Bed Levelling X axis offset
I upgraded my Ender 3 with the CR Touch, and updated the firmware (contacted Creality directly to get the correct version). I got Marlin 2.0.6. However when I try the bed levelling feature the first point (nearest to the origin), always starts with…
Fusco Bhonsle
- 1
- 1
-1
votes
1 answer
Ender 3 printer won't auto home
After building my Ender 3 printer, installing the CR touch auto bed leveling kit, and the Ender-3 Marlin2.0.6 CR-Touch or BLTouch firmware for it. I turned it on and tried to auto home but it just made a little noise and then displayed "Homing…
3dNovice
- 9
- 3