3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [mriscoc]

Firmware for Ender 3 V2

11 questions
2
votes
1 answer

How do I fix deformities when printing on my Ender 3 V2?

Being a newbie in 3D printing, I have some trouble with my prints. After removing wiggle room from the X axis and the bed, there are deformities even on simple prints. The first layer turns out okay-ish but there seems to be some stringing that…
Barth
  • 61
  • 4
1
vote
1 answer

How to physically wire a (ADXL345) accelerometer for Input Shaping (Resonance Compensation) support on for a Ender 3 V2 printer?

I'm looking into Input Shaping (Resonance Compensation) to compensate for vibration on an Ender 3 V2. I found the "Official Creality G-Sensor ADXL345 Vibration Compensation Sensor for Sonic Pad 3D Printed Smart Pad" which I guess, unlike the name…
Bob Ortiz
  • 374
  • 1
  • 15
1
vote
2 answers

Ender 3v2 nozzle plunging into bed after finishing mesh (only changed springs)

Yesterday I was printing just fine. Today I put the new springs that I bought from Amazon. Swapped them out, went to level things and my Z-offset was of course way off. I have the Ender3V2-422-BLTUBL-MPC-20230904.bin firmware from mriscoc I homed…
Joleme
  • 11
  • 2
1
vote
0 answers

Aquila X3 small firmware does not flash to board

I'm using the MRiscoCProUI firmware on my Aquila X3 printer, but when I enable more features in the firmware, I'm unable to flash the printer. I already tried several options and independently of the ones chosen, when the firmware gets to around 230…
Gonçalo Cardoso
  • 111
  • 3
1
vote
0 answers

Uneven mesh after perfect auto tramming?

BLTouch enabled Ender 3 w/4.2.2 board running mriscoc's Professional firmware. How is it that the auto tramming can report the corners of the bed to be level, and then immediately afterwards it produces this mesh? What am I missing?
benram14159
  • 81
  • 1
  • 8
0
votes
1 answer

How to successfully flash a DACAI LCD screen of a Creality Ender 3 V2?

I thought I had two identical Ender 3 V2 printers, the main board in both is v4.2.2 but it turns out they came with a different LCD screen. I flashed the firmware on both printers to mriscoc firmware and tried to also flash both LCD…
Bob Ortiz
  • 374
  • 1
  • 15
0
votes
0 answers

Is the BFPTouch interchangable with the BLTouch for mriscoc firmware without custom changes to Marlin?

I have two Creality Ender 3 V2 printers with a v4.2.2 board. One printer has the official CRtouch and one is nearly stock. I can simply buy another CRTouch, but I found an exciting DIY project called BFPTouch, and I happen to have almost all the…
Bob Ortiz
  • 374
  • 1
  • 15
0
votes
1 answer

Is there a way to send a thumbnail to the printer LCD screen when printing over USB from OctoPrint?

I'm using Cura Thumbnails using a plugin in Cura 5.5. Also, I use the Marlin-based mriscoc firmware on a Creality Ender 3 V2 with OctoPrint using OctoPi on a Raspberry Pi 4. The firmware supposedly supports Thumbnail's preview when printed from an…
Bob Ortiz
  • 374
  • 1
  • 15
0
votes
0 answers

Why is MPC better than PID for 3D printers, and (why) is it more useful for 'high-power heaters'?

The YouTube video 'PID vs MPC' from Mark Misin Engineering Ltd perfectly demonstrates that Model Predictive Temperature Control (MPC) is more powerful than Proportional-Integral-Derivative (PID). Marlin implemented MPC as described in Marlin's MPC…
Bob Ortiz
  • 374
  • 1
  • 15
0
votes
1 answer

How does Adaptive Mesh Leveling (AML) actually work?

I recently started using the new mriscoc firmware for my Creality Ender 3 V2 and it is truly performing above expectations. Even considering that Jyers UI was already a step up from the original Creality firmware. I'm trying to understand how the…
Bob Ortiz
  • 374
  • 1
  • 15
0
votes
1 answer

During a print, why must I continually adjust the Z offset to a more neagative number to keep the nozzle from air printing?

The nozzle is not clogged. After an adjustment, I get two to three good printed layers then the nozzle begins to lift away from the print. If I do not adjust the Z offset more negatively, then the print begins to go airborne in very small…
Robert Spring
  • 1
  • 1